Plexiglas® GS 0Z09 (209) Cast Acrylic

طلب ل السعرطلب ل عينةطلب ل تشاورطلب ل قبل الفاتورة

الوثائق الفنية

Description: PLEXIGLAS® GS cast acrylic

تفاصيل

نوع المنتج

البوليمر > الاكريليك والبوليمرات الاكريليك

تطبيقات

صناعة البوليمرات > أنبوب أنابيب البثق
صناعة البوليمرات > البثق ملامح ورقة
صناعة البوليمرات
صناعة البوليمرات > بالحرارة

منتج

Evonik

المورد

إيفونيك إيران ، PLEXIGLAS

مزايا
  • absolutely colorless
  • clearbreak-resistant
  • unequalled resistance to weathering and ageing
  • high-quality surface and planarity; brilliant or satin
  • good resistance to dilute acids
  • limited resistance to organic solvents
  • good resistance to alkalis
  • very easy to work
  • similar to hardwood
  • easy to thermoform over wide range of conditions
  • easily and firmly bonded, e.g. with reaction adhesives
  • burns more or less like hardwood
  • very little smoke generation
  • max. service temperature approx. 80 °C
تطبيقات أخرى

sheets, blocks, tubes, round and square rods2 to 160 mm solid sheet / block thickness standard size up to 3050 x 2030 mmmore than 50 standard colors

معلومات تقنية

كمية قدر وحدة التعلیق
خصائص المظهر
Refractive index 1.491 clear grade; ISO 489@Thickness 3.00 mm
الخصائص الفيزيائية
Density 1.19 g/ml ISO 1183
الخصائص الحرارية
Heat Deflection temperature 115 ºC ISO 75;at 0.46 MPa
Vicat softening temperature 115 ºC ISO 306, Method B 50
Thermal Expansion 70.0 µm/m-°C DIN 53752A@Temperature 0.000-50.0 °C;Linear
Thermal Conductivity 0.190 W/mk DIN 52612
Maximum Service Temperature 200 ºC IR Radiator
U Value 5.3 W/m² DIN 4701; for 5 mm
U Value 4.4 W/m² DIN 4701; for 10 mm
U Value 5.8 W/m² DIN 4701; for 1 mm
U Value 5.6 W/m² DIN 4701; for 3 mm
Specific Heat Capacity 1.47 J/gºC
Maximum Service Temperature 80.0 ºC Permanent
Heat Deflection temperature 107 ºC ISO 75;at 1.8 MPa
Flameability @Thickness 1.60 mm
flash point 425 ºC Ignition Temperature; DIN 51794
خصائص ميكانيكية
Tensile Stress at break-MD 80.0 MPa ISO 527-2/1B/5
(Charpy Impact Strength(unnotched 15.0 kJ/m² ISO 179/1fU
(Izod impact strength(notched 1.60 kJ/m² ISO 180/1A
Elongation at break-MD 5.5 % ISO 527-2/1B/5
Tensile modulus-MD 3300 MPa Short Time Value; ISO 527-2/1B/1
Coefficient of friction 0.50 plastic/steel
Coefficient of friction 0.45 steel/plastic
Coefficient of friction 0.80 plastic/plastic
Poisson's ratio 0.37 dilation speed of 5% per min; up to 2% dilation; ISO 527-1@Temperature 23.0 °C
Tensile Stress at break-MD 110 MPa ISO 527-2/1B/5@Temperature -40.0 °C
Ball indentation Hardness 175 MPa H961/30; ISO 2039-1
Flexural strength 115 MPa 5mm/min (80x10x4 mm); ISO 178
Abrasion 20 - 30 Haze, Abrasion resistance in Taber abrader test (100 rev.;5.4 N; CS-10F); ISO 9352%
shear modulus 1700 MPa Dynamic Shear Modulus at 10 Hz; ISO 537
Tensile strength 40.0 MPa ISO 527-2/1B/5@Temperature 70.0 °C;Ultimate
Compressive Strength 110 MPa ISO 604; at Yield
الخواص الكيميائية
Water absorption 2.1 % Max. Weight Gain During Immersion; ISO 62, Method 1; at Saturation
Moisture Vapor Transmission 55.0 cc-mm/m²-24hr-atm
Permeability 4.5e-15 g cm/cm2 h Pa to N2
Permeability 8.3e-15 g cm/cm2 h Pa to Air
Permeability 2.0e-14 g cm/cm2 h Pa to O2
Water absorption 0.48 % 24hrs, 23°C from dry state; ISO 62, Method 1
Permeability 1.1e-13 g cm/cm2 h Pa to CO2
Moisture Expansion 0.50 % Possible Expansion due to heat and moisture
الخواص البصرية
Transmittance 92 % clear grade; DIN 5036, Part 3@Thickness 3.00 mm;Visible
Transmittance 85 % clear grade, 3 mm, DIN EN 410
Transmittance 0.00 % UV ; clear grade@Thickness 3.00 mm
Reflection Coefficient 0.040 (clear grade, Reflection loss in the visible range (for each surface) @Thickness 3.00 mm;Visible(0-1
Absorption in the Visible Range <0.05 % clear grade, 3 mm
الخواص الكهربائية
Dielectric Strength 30.0 Kv/mm DIN VDE 0303, Part 2
Comparative Tracking Index 600 V DIN VDE 0303, Part 1
Dissipation Factor 0.020 DIN VDE 0303, Part 4@Frequency 100000 Hz
Dielectric Constant 3.7 DIN VDE 0303, Part 4@Frequency 50 Hz
Dissipation Factor 0.060 DIN VDE 0303, Part 4@Frequency 50 Hz
Shielding Effectiveness 30 dB Weighted Sound Reduction Index at 6 mm
Shielding Effectiveness 26 dB Weighted Sound Reduction Index at 4 mm
Volume resistance >1.00e+15 ohm-cm DIN VDE 0303, Part 3
Surface Resistance 5.00e+13 ohm DIN VDE 0303, Part 3
Dielectric Constant 2.8 DIN VDE 0303, Part 4@Frequency 100000 Hz
Dielectric Constant 3.6 DIN VDE 0303, Part 4@Frequency 50 Hz
Dielectric Constant 2.7 DIN VDE 0303, Part 4@Frequency 100000 Hz
Shielding Effectiveness 32 dB Weighted Sound Reduction Index at 10 mm

اتصل بالمورد

للاتصال الموردين من هذه الماد وتسجيل طلب للحصول على سعر، عينة، التشاور أو قبل الفاتورة، يرجى ملء استمارة الطلب.

معلومات شخصية

معلومات الشركة

معلومات المشروع